EVO Manufacturing

Jeep JK's are known to run hot, especially while off-road. The EVO MFG JK Hood Breach allows optional ventilation reliefs to increase air flow in the engine compartment allowing for cooler running temperatures. Made from thick Aluminum Alloy sheet and laser cut with ventilation slots, the two piece ..

The EVO Manufacturing Centered Fairlead Light Mount is a great way to add auxiliary lights to any bumper or winch plate with a built in fairlead mount...

EVO HD SwayBar EndLinks are made of solid hex bar and are adjustable in length. They come with 1/2" studded Teflon lined rod ends, 3/4" hex bar linkage and all necessary hardware. Offered in lengths ranging from 5.5" to 15.9" Use these to beef up a very important component of your suspension system...

EVO MFG 100% bolt on automatic transmission skid plate can be installed with factory hardware. Powder coated black for maximum corrosion resistance. Proudly Made 100% In USA...

EVO MFG Overland Control Arm Drop Brackets for the Jeep Wrangler JL gives improved ride quality by maintaining factory flat control arm angles which remedy much of the bump steer associated with lifting a Jeep. You will also achieve better performance in the front end suspension, such as, improved b..

Proudly Made 100% In USA...

EVO MFG side mount frame bracket fits all joints that are 2 5/8” wide. Laser cut and CNC bent from 3/16" steel. Tongue and groove construction allows for easy assembly. Can be used for 3 link, 4 link or radius arm suspension configurations. Comes un-welded. Proudly Made 100% In USA...

The original EVO MFG C2 Front Axle Reinforcement Gussets are made out of 3/16" laser cut, CNC bent steel and are engineered to seriously beef up your Jeep JK Wrangler's front axle C's. These gussets are a direct fit to the JK Dana 30, Dana 44 and even 2WD axles. Each purchased kit will gusset a comp..

EVO MFG Front D-Ring Mounts are a direct bolt-on design for the EVO MFG front bumpers. Laser cut from 3/4" steel plate and powdercoated in a textured black finish. Proudly Made 100% In USA...

The EVO MFG Rock Skins are side armor plates are CNC bent and laser cut from 3/16 steel. These can be used with all factory Jeep sliders and steps as well as all aftermarket frame mounted rock sliders. The Rock Skins protection contours around stock and aftermarket fenders (factory mounting location..

EVO MFG JK Vacuum Relocation Kit is a simple install with factory hardware and works with all bumpers. Relocates factory vacuum cylinder to allow for all winch applications. No drilling is required...

The Evo Manufacturing Front or Rear Extended Brake Lines are designed as a direct replacement for the factory front and rear brake hoses in your Jeep Wrangler JK. With a stainless steel braided covering, these brake hoses can withstand more pressure than factory hoses to provide better braking perfo..

EVO HD SwayBar EndLinks are made of solid hex bar and are adjustable in length. They come with 1/2" studded Teflon lined rod ends, 3/4" hex bar linkage and all necessary hardware. Offered in lengths ranging from 5.5" to 15.9" Use these to beef up a very important component of your suspension system...

The EVO MFG License Plate Relocate/Rotopax Can Mount enables you to mount your license plate in the center of your spare tire so that it can easily be seen and is away from the bumper, which helps avoid snags on the trail. Additionally, it can be used as a Rotopax Can mount. By utilizing this featur..

The EVO Manufacturing Front Adjustable Trackbar is built with thick DOM steel tubing for a strong upgrade to your Jeep Wrangler JL or Gladiator JT. Adjustability allows you to recenter the axle after installing a lift kit to correct the steering and suspension geometry. A combination of rubber bushi..

EVO MFG's Front Shock Relocation Brackets grant you an increase in shock clearance between the frame and larger aftermarket shocks on the front of your JK. This kit also increases shock clearance with frame when longer lift shocks are installed at extreme flex situations. Powder coated black. Proudl..

The EVO MFG HD Protek Transmission Crossmember is constructed from 3/16” plate steel that is fully boxed and section welded to keep the crossmember straight and true minimizing heat wrap. Easy installation with no cutting or drilling required. Powdercoated for a clean finish and corrosion resistance..

The EVO Plush Ride Front 2.5" Lift Coils Springs will not only lift your Jeep Wrangler JL 2-door or Unlimited JL 4-door but will give you exceptional ride quality. 4-door sport & Sahara models will see a height gain that is similar to a stock Rubicon, while the 2-door models will see slightly higher..

The EVO MFG JK Rear Rockstops are a rear air bump stop system specifically designed to fit with the 2007 and newer Jeep Wrangler JK's. The addition of air bumps allow for suppressed bottoming out forces which therefore transfers less motion and jarring to the driver's seat. This kit works with stock..

The EVO MFG ProTek Rear Shock Skids for Jeep Wrangler JL 2-door & Unlimited JL 4-doors comes with both driver and passenger sides skids and is made from 3/16 steel. The Shock Skids are powder-coated black for rust and corrosion protection. ProTek Rear Shock Skids are designed to take a beating and p..

The EVO MFG C2 Axle Gussets for Jeep Wrangler JL's are designed to backbone the axle endforging "Cs" with CNC formed 3/16" laser cut steel on both upper and lower axle Cs keeping them aligned and protected. These gussets are a direct fit for JL 2 & 4-door Dana 44 Rubicon (M210) and Dana 30 Sahara/Sp..

EVO MFG Low Profile Quick Connect Brackets allow Adjustable Tire Coverage (frame to outer tire) from 16” to 18”. Shortening of mounting tube may be required for lengths over 18”. Easy installation and simple pull pin removal make keeping your Jeep street legal a breeze. Powder coated for clean finis..

Complete the look of your JK by extending your armor up the B-Pillar with the EVO MFG B-Pillar Rockskin. The profile is designed to match existing EVO MFG armor and hardware is included to match either the EVO MFG Rockskins or EVOMFG Boatside Bomber. This part does require drilling into the body she..

EVO MFG Tailgate Plate is a 2 piece system that is pre-drilled for your license plate. Fits both wide and tall tailgate vents without removal. Powder coated for clean finish and corrosion protection. Easy install using factory hardware Proudly Made 100% In USA...