Tailgates

Tired of your tailgate slammin' into you EVERY TIME you go for your gear ? The Gate Keeper will do the trick,one hand opens it with a flick of the wrist no knobs,clips or spring locks. Rubber foot leaves no marks,closes compact & out of the way...

..

How about a rugged steel replacement for your long suffering Tailgate? Our Tailgates are precision engineered for an exact fit. All holes are pre-punched and it comes already primed...

The Crown Automotive Steel Tailgate is a replacement for the factory original tailgate used in early TJ Wranglers up to 2002. If you are replacing the tailgate on a Wrangler 97-02 then you can swap all of your parts over and be back on the road once the paint has dried. The Crown tailgate has holes ..

..

EVO MFG Tailgate Vent Delete Plates are pre-drilled to accept a license plate. Powder coated for a clean finish and corrosion protection. Easy install using factory hardware. Factory vent removal required. Works with both wide and tall tailgate vents. Proudly Made 100% In USA...

EVO MFG Tailgate Plate is a 2 piece system that is pre-drilled for your license plate. Fits both wide and tall tailgate vents without removal. Powder coated for clean finish and corrosion protection. Easy install using factory hardware Proudly Made 100% In USA...

Convenience and safety! Lift your Jeep's® AEV Heat Reduction Hood with just one hand. Dual gas shocks raise and hold the hood in an upright position. Simply raise the hood about a foot and as the support shocks take over, just let go! Works like a Jeep hardtop lift gate. Slight downward pressure clo..

When you are restoring your Jeep CJ, you want the parts that will make it look original. The Omix Jeep Logo Steel Tailgate is an official restoration part, with officially licensed logo. Made to original standard and punched to accept original hardware. Finished in a black primer coat to reduce prep..

With the JL Adapter Bracket added on to The Judge Flag Mount you will be able to relocate your factory back up camera so you do not lose the factory function while you let your flag fly. This is the bracket only, shown on the flag mount for visual purposes only...

Since the JL Wrangler factory license plate mount is built into the stock rear bumper, you may need to find a new way to mount your rear license plate once you install an aftermarket rear bumper. The Kentrol BackSide License Plate Mount with LEDs makes license plate relocation a breeze. Additionally..

The hollow steel tailgate on a Jeep Wrangler is not intended to hold a lot of weight. If you have larger tires or use bike racks frequently you may have noticed that your tailgate shell is starting to crack at the welds. The Mopar Steel Tailgate will reset the damage and restore your Jeep to its fac..

..

..

If you have lost the vent from your JK Wrangler factory tailgate, seal up the hole with a new Mopar Tailgate Exhauster. This vent allows air to pass through when you are closing the tailgate so you do not blow out your soft top windows from too much pressure. If the exhauster is missing you could be..

..

..

..

Replace that rusty black spare tire stop with this highly polished stainless steel unit. Includes all fasteners. Installs in minutes. For CJ7 & '87-'95 Wrangler...

..

This licensed Jeep logo Steel Tailgate from Omix completes any well done restoration or damage repair. Complete with a new seal this tailgate is coated in a black primer finish that is ready for paint and assembly. Hardware such as hinges, cables and latches are sold separately...

How about a rugged steel replacement for your long suffering Tailgate? Our Tailgates are precision engineered for an exact fit. All holes are pre-punched and it comes already primed in black...

..

The original replacement Steel Tailgate from Omix is for the Wrangler YJ. If you Jeep is ready for some preventative body work or you are repairing collision damage, this tailgate is made to original standards and accepts all internal components and hardware. Black primer coat is applied at the fact..