EVO Manufacturing

The EVO MFG HD Protek Transmission Crossmember is constructed from 3/16” plate steel that is fully boxed and section welded to keep the crossmember straight and true minimizing heat wrap. Easy installation with no cutting or drilling required. Powdercoated for a clean finish and corrosion resistance..

The EVO Plush Ride Front 2.5" Lift Coils Springs will not only lift your Jeep Wrangler JL 2-door or Unlimited JL 4-door but will give you exceptional ride quality. 4-door sport & Sahara models will see a height gain that is similar to a stock Rubicon, while the 2-door models will see slightly higher..

The EVO MFG JK Rear Rockstops are a rear air bump stop system specifically designed to fit with the 2007 and newer Jeep Wrangler JK's. The addition of air bumps allow for suppressed bottoming out forces which therefore transfers less motion and jarring to the driver's seat. This kit works with stock..

The EVO MFG ProTek Rear Shock Skids for Jeep Wrangler JL 2-door & Unlimited JL 4-doors comes with both driver and passenger sides skids and is made from 3/16 steel. The Shock Skids are powder-coated black for rust and corrosion protection. ProTek Rear Shock Skids are designed to take a beating and p..

The EVO MFG C2 Axle Gussets for Jeep Wrangler JL's are designed to backbone the axle endforging "Cs" with CNC formed 3/16" laser cut steel on both upper and lower axle Cs keeping them aligned and protected. These gussets are a direct fit for JL 2 & 4-door Dana 44 Rubicon (M210) and Dana 30 Sahara/Sp..

EVO MFG Low Profile Quick Connect Brackets allow Adjustable Tire Coverage (frame to outer tire) from 16” to 18”. Shortening of mounting tube may be required for lengths over 18”. Easy installation and simple pull pin removal make keeping your Jeep street legal a breeze. Powder coated for clean finis..

Complete the look of your JK by extending your armor up the B-Pillar with the EVO MFG B-Pillar Rockskin. The profile is designed to match existing EVO MFG armor and hardware is included to match either the EVO MFG Rockskins or EVOMFG Boatside Bomber. This part does require drilling into the body she..

EVO MFG Tailgate Plate is a 2 piece system that is pre-drilled for your license plate. Fits both wide and tall tailgate vents without removal. Powder coated for clean finish and corrosion protection. Easy install using factory hardware Proudly Made 100% In USA...

The EVO MFG Winch Fairlead Light Mount is constructed from 3/16” steel plate which is CNC laser cut and formed with precision CNC press brake. Proudly Made 100% In USA...

EVO HD SwayBar EndLinks are made of solid hex bar and are adjustable in length. They come with 1/2" studded Teflon lined rod ends, 3/4" hex bar linkage and all necessary hardware. Offered in lengths ranging from 5.5" to 15.9" Use these to beef up a very important component of your suspension system...

EVO MFG 3/16” steel skid protects the expensive to replace factory transmission crossmember, exhaust crossover and the exhaust loop on the Wrangler JK. 100% bolt on with factory and supplied hardware. Works on both manual and automatic transmissions. Powder coated black. Not recommended for JKs with..

Now Wrangler JL owners can covert their current short or mid arm suspension to a long arm kit with the High Clearance Long Arm Upgrade from EVO Manufacturing. This kit is designed to reuse some of the existing suspension components such as the coil springs, swaybar links, and bump stop extensions. T..

..

The Jeep Wrangler JK and JKU's Evap Canister is venerable to potential damage while on the trail. EVO MFG's ProTek Evap Skid protects the evap canister from trail damage. The EVO evap skid is boxed in on all four sides for the ultimate protection. The install process is easy and there is no need to ..

This EVO MFG product is designed to increase the Wrangler JK axle housing strength by 30% while incorporating dual seals to prevent debris from entering the axle tubes. Combining these two tried and true technologies will not only increase the strength of your axle housing, but will also help to pre..

CNC machined from high strength thermoplastic. Proudly Made 100% In USA...

The EVO MFG Rock Skins are side armor plates are CNC bent and laser cut from 3/16 steel. These can be used with all factory Jeep sliders and steps as well as all aftermarket frame mounted rock sliders. The Rock Skins protection contours around stock and aftermarket fenders (factory mounting location..

The EVO Manufacturing Alumilite Rear Bumper for Jeep Wrangler JL & Unlimited JL is designed to protect the rear of your Jeep Wrangler. This sleek rear bumper replaces the factory bumper with a strong and lightweight aluminum bumper. This bumper is equipped with Jeep parking assist backup sensor knoc..

The Evo Manufacturing Front or Rear Extended Brake Lines are designed as a direct replacement for the factory front and rear brake hoses in your Jeep Wrangler JK. With a stainless steel braided covering, these brake hoses can withstand more pressure than factory hoses to provide better braking perfo..

EVO MFG Air Compressor Mount Bracket cleanly mounts the ARB small and large air compressors (not twin) high in the engine compartment. Fits all year JKs. Simple install with factory hardware. No drilling or cutting, Laser Cut, CNC bent, powder coated for clean finish and corrosion protection. Proudl..

Many JK owners remove the front fender liners, either to accommodate aftermarket fenders, suspensions, or encourage engine compartment airflow. This modification leaves the wiring harness connector vulnerable to trail debris. The EVO Mini Liners provide protection to this connector left exposed by t..

The EVO Manufacturing Rear Adjustable Trackbar is built with thick DOM steel tubing for a strong upgrade to your Jeep Wrangler JL. Adjustability allows you to recenter the axle after installing a lift kit to correct the steering and suspension geometry. A combination of rubber bushings and spherical..

EVO Rear Shock Extensions give you the ability to relocate the shock mounting and swaybar mounting hole to adjust for a lifted Jeep Wrangler JL 2 and 4-door without the need to replace shocks. Instead of purchasing new shocks, these extension brackets attach to your existing shocks to accommodate li..

The EVO MFG HD Protek Transmission Crossmember is constructed from 3/16” plate steel that is fully boxed and section welded to keep the crossmember straight and true minimizing heat wrap. Easy installation with no cutting or drilling required. Proudly Made 100% In USA...